[Penzfan]

Just bought a $12 Amazon laser. I have zeroed it in yet. It works. I plan to use loctite on it. View attachment 456957
View attachment 456955

Had one of those, they move around ALOT. Went with the Armalaser T23 and have no issues. Good Luck...

 

[Penzfan]

My G3 with an Armalaser TR23 laser, Tandemkross front Fiber Optic and Versacarry leather Commander Holster...
Love it

 

[Steyr]

PT-111 Mil Pro is smaller than the PT-140 and PT-145.

Yes smaller caliber

 

[waltosha]

Hi everyone one of my biggest mistakes was trading my millennium Pt145 with night sights I would definitely buy any millennium Pt145 with or without night sights I can find

 

[9mmHartsell]

My new G3X that i got when it came out.

 

[Master Chief]

My G3 with an Armalaser TR23 laser, Tandemkross front Fiber Optic and Versacarry leather Commander Holster...
Love it

View attachment 479691

The only thing that would make your G3 cooler, is if it had the T.O.R.O slide on it. Love the OD color!

 

[Buckeye!]

My G3X & G2C

 

[Master Chief]

my new G3C TORO.I love this gun!

 

[Bubbas358]

Here is just another G3c, but it is my G3c.....

 

[Bubbas358]

Yup, crappy pic of the night sights, but that was all the phone could do for focusing......

 

[Master Chief]

Yup, crappy pic of the night sights, but that was all the phone could do for focusing......

Which sights? Nice piece BTW! I’m looking for one with an OD Green grip.

 

[Bubbas358]

Which sights? Nice piece BTW! I’m looking for one with an OD Green grip.

XS DXT2 Big Dots. DXT2 Big Dot Night Sights - Taurus I have found that these work very well for me on all my handguns that I own (the ones I can get them for). I prefer the green, rather than the orange, as my eyes see that fastest.

 

[Mr. Zorg]

My one and only Taurus G2C in 40 S&W. I haven't been to the range with it yet, but I'm looking forward to doing so.

 

[A45ACP]

Here's a 3D printed EveryGunPart PT111 G2 that failed (CoPA nylon). The frame cracked in 2 places. I've since reprinted it using 3D Fuel Pro PLA and after running thru two magazines, it is still intact.

EDIT: 3D Fuel Pro PLA:

 

[DeltaBravoKS]

Here's a 3D printed EveryGunPart PT111 G2 that failed (CoPA nylon). The frame cracked in 2 places. I've since reprinted it using 3D Fuel Pro PLA and after two magazines, it is still intact.

View attachment 493016

Wait! You 3D printed the entire polymer frame of a PT111G2?

 

[A45ACP]

Yes, and I embossed the model & SN on the other side of it. The fit is too tight at the rear, on my first Pro PLA try I cracked the frame putting the rear pins in. Scaled it to 100.5% on 2nd print. Safety lever remains too tight as well. Need to file that area out some more, but it functions OK otherwise.

EDIT: The fit was OK using a 100% scaled frame. I had the safety lever misaligned. These are a PITB to put back together!

 

[Reese]

 

[Mr. Zorg]

Nice!!!

How do you like that Olight Baldr S? I've purchased one with green laser but I haven't done anything with it yet. I haven't even taken it out of the box.

 

[Reese]

Nice!!!

How do you like that Olight Baldr S? I've purchased one with green laser but I haven't done anything with it yet. I haven't even taken it out of the box.

It's a good light/laser combo...mine is also the green laser.

I especially like the quick release feature of the Olights, being able to adjust it where you want it is nice too.

The magnetic charger is cool but I wish you could change the batteries.Was going to carry a pistol with the Baldr Pro R, flicked it on and it came on and went right off...dead battery.....and it takes at least an hour or more to charge up. It would be nice to be able to just swap out the battery in that situation like I do with my Streamlights. One advantage of the Bakdr S is a low battery indicator like the Pl Mini 2s have also.

Still it is a nice light...just make sure you keep the battery charged up.

 

[gunsmoke92]

Nothing special, just a little G3c I picked up. My last gun purchase for 2022! Sorry, this is the only shot I have right now.