650 problem
Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: 650 problem

  1. #1
    Member
    Member #
    3522
    Join Date
    Jun 2008
    Posts
    36
    Liked
    0 times

    650 problem

    At the range after 20 rounds of 357mag the trigger did not reset with 3 live rounds in the cylinder
    I tried to open the cylinder and is stuck
    I pulled the trigger forward with my hand and shoot the rest of the rounds (can't leave the range with live ammo in a broken gun)
    Can't open the cylinder any ideas?
    Ill call taurus right now to
    Thanks

  2. #2
    Moderator Emeritus

    Member #
    1686
    Join Date
    Nov 2007
    Location
    Kentucky
    Posts
    15,932
    Liked
    956 times

    Re: 650 problem

    If I had to guess, which this is? Check the rod that holds the extractor, it might have backed out, or the extractor might have moved enough to jam it.



    ROBBY
    Board Of Directors KC3 http://www.kc3.com/index.html
    NRA Member, GOA Member, NAGR member


  3. #3
    Member
    Member #
    6394
    Join Date
    Jan 2009
    Location
    Green,wet and freindly
    Posts
    32
    Liked
    0 times

    Re: 650 problem

    I had the same problem with mine, after it gets hot the cylinder binds at the forceing cone because the gap between the cylinder face and forceing cone is not even. Its closer at the top than at the bottom, a gun smith could fix it fast.

  4. Remove Advertisements
    TaurusArmed.net
    Advertisements
     

  5. #4
    Member
    Member #
    3522
    Join Date
    Jun 2008
    Posts
    36
    Liked
    0 times

    Re: 650 problem

    It was cold when I got home and I am new to revolvers but I tried everything and could not open the cylinder
    Last time at the range I shoot 100 38spl and 40 357 and it was fine
    Anyway it is in a box for a longggg vacation home lol after the call to CS
    This is my first taurus going back and I had a lot of guns from them so ill give it another chance (because I can shootit so good)
    Thanks guys ill post a range report when I get it back

  6. #5
    Member
    Member #
    3522
    Join Date
    Jun 2008
    Posts
    36
    Liked
    0 times

    Re: 650 problem

    just got it back
    it was quick 4 weeks
    it says that the bolt was replaced
    what is the bolt on a revolver?
    need to go to the range

  7. #6
    Senior Member
    Member #
    9682
    Join Date
    Aug 2009
    Posts
    1,088
    Liked
    1 times

    Re: 650 problem

    The bolt is the little dingus that projects upward from the frame and pushes into one of the slots in the cylinder. It locks the cylinder and keeps it in battery as the hammer drops.
    NRA Life Member

  8. #7
    Member
    Member #
    3522
    Join Date
    Jun 2008
    Posts
    36
    Liked
    0 times

    Re: 650 problem

    aha thanks
    so the little thing made the whole gun lock?
    i have to go to the range tomorrow i have 100 rounds of 357 and ill use them all
    after that i can trust this gun again

  9. #8
    Senior Member
    Member #
    9682
    Join Date
    Aug 2009
    Posts
    1,088
    Liked
    1 times

    Re: 650 problem

    Hard to say what happened. The bolt is spring loaded and should be free to drop down when you pull the cylinder to the side to open it. If something went wrong with it preventing it from dropping down, that might prevent the cylinder from opening. Likewise, rough edges on it might get it stuck in the cylinder slot, preventing the cylinder from opening. Is sounds a bit far fetched that that was the whole problem, but it could be.
    NRA Life Member

  10. #9
    Member
    Member #
    9020
    Join Date
    Jun 2009
    Posts
    34
    Liked
    0 times

    Re: 650 problem

    thats sucks I hope taurus get your gun fix and back to you, do let us know what was the problem with it if taurus tell you. thanks

  11. #10
    Member
    Member #
    3522
    Join Date
    Jun 2008
    Posts
    36
    Liked
    0 times

    Re: 650 problem

    i got it back already from Taurus
    got at the range to day and after 100 38spl and 50 357 mag it works just fine

 

 
Page 1 of 2 12 LastLast

Sponsored Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Search tags for this page

how to fix taurus 650 cylinder jam
,
problems with taurus 650
,
taurus 650 357 mag ammo jamming
,
taurus 650 cia cylinder jams with .357 rounds
,
taurus 650 cylinder jam
,

taurus 650 problems

,
taurus 650 problems video
,
taurus 650 trigger
,
taurus 650 trigger stuck
,
trigger problem taurus 650
Click on a term to search for related topics.