after market sights for Mil pro ??

[Zach_Smith]

Does any make any thing to replace the henines, if so and you can you recommed any, low priced models (i dont want to pay more for th sights than i paid for the gun) also does any one know if they make those laser grips that ive saw for other guns.

also how hard is it to install sights?

[dawgfvr]

Recommend you do a search for "Sights" Lots of info already gone over on this forum in that area

[afrats]

I also recommend that you get someone that knows what they are doing to put the sights on for you. There are too many little things that could happen and affect how your gun shoots.

[tdyoung58]

I painted mine with florescent yellow, makes them much more visible.

If you want to replace them, it's not very difficult to do, actually very easy, just remember to mark the center line before you remoeve the old ones so you can line the new ones up properly, I use a pencil, which comes off very easy

http://www.cheaperthandirt.com/46042-56448-2096.html for some sights, for a Mill Pro

[WildRice]

I just ordered some Williams Fire Sights from cheaperthandirt.com for my 3rd gen Mil Pros (PT-145 and PT-111). I will give a review in the future once I receive them. Older Mil Pros have non-Heinie screw down sights, where as 3rd gen Mil Pros have Heinie dovetailed sights with allen lock down bolts. CTD sells both types for Taurus pistols, so make sure you order the correct ones! To add to the confusion, the CTD photo for the dovetail sights is that of the non-dovetail sights, but the Williams part number is for the correct dovetailed type. We will see what I receive.

[Zach_Smith]

i know, i have a third gen and i thought pic was strange

[jcan]

the tactical store.com has them with free shipping

[smithlock]

Just remember something, guys. (I've had no support or feedback on my earlier suggestion). When you remove that Mil-Pro third gen. front sight, heat it up w/a hair dryer and carefully tap a 1/16th hex into the metric allen screw. (instead of the recommended metric hex). It'll turn right out. Drifting out w/brass punch is a no-brainer.

This will keep you from rounding out allen screw (it's a 1.5mm) and creating difficult removal. When you finish, you'll still have a good hex wrench and usable screw. This is not "kosher" but I've done it twice now with two guns and thought I'd try to help.

smit

[WildRice]

I installed Williams Fire Sights on my PT111 and PT145. The stock sights are dovetailed Heinie "straight eight" sights, so I ordered dovetail Fire Sights (model #70897). For older Mil Pros with non-dovetailed sights, you will want model #70268. I marked the slide as to the windage of the old sights which were pretty much dead center on each pistol. The stock front Heinie sight needs a 1.5 mm Allen wrench to loosen and the rear a 2 mm Allen wrench. After loosening these set screws, I used a brass drift to tap them out from the bare slide. There was a thin layer of gel-like adhesive under the sights that I left in place as it may help hold the new sights.

The new sights drifted in place with the same amount of tapping effort (i.e. a good fit). The front Williams set screw is .050" Allen and the rear was 1/16" Allen (the stock Heinies are metric). I added blue Loctite to the screw threads. There are no wrenches or instructions included!

The rear Fire Sight has two orange fiber optic rods that gather a lot of light and are very bright, especially with light from above. The front is a thicker, light-green, single rod which is even brighter. These should be easy to pick up with fast shooting in both day light and dim light. They will not glow in no light. The rear is ramp shaped and snag free. The front has a few sharps corners. I performed some rough measurements as follows (in mm, top of slide to top of sight):

Heinie PT111 Heinie PT145 Williams Fire Sights
Front 5.4 5.8 5.5
Rear 5.6 5.6 5.7

This should raise the point of impact on my PT145 (which hit a low as stock) and not significantly change the POI on my PT111 (which hit just slightly low as stock).

The fire sights have a rather narrow rear notch with thin light bars. I prefer a wider notch and broader light bars for target shooting. There is not much if any material that I can remove to either lower the height of the front sight or widen the rear notch, as the fiber optic rods are close to the black edges. I will try these out at the range this weekend. I predict these will be very good combat sights, but only so so target sights. My PT145 should hit closer to point of aim.

[dawgfvr]

Love my 2nd generation DAO...

New sights just screwed in...put a little loc-tite on them first.