No More Results
About paulrabe78

Basic Information

Date of Birth
November 1, 1978 (35)
About paulrabe78
Location:
Rochester, MN

Signature



Taurus PT1911 SS
Taurus 24/7 .45 ACP OSS
Taurus 24/7 .40 S&W OSS
Taurus 24/7 9mm OSS
Taurus 738 SS
NRA Member

Statistics


Total Posts
Total Posts
3,563
Posts Per Day
1.51
Albums
Total Albums
1
Total Pictures
6
General Information
Last Activity
Yesterday 11:39 AM
Join Date
02-09-2008
Referrals
0

218 Likes

Page 1 of 15 12311 ... LastLast
  1. edstuff
    edstuff liked post by paulrabe78 On thread : I'm so bad
    Nice group of firearms.
    Liked On: 07-18-2014, 12:23 PM
  2. bamashooter
    bamashooter liked post by paulrabe78 On thread : PT 1911 sights
    The rear sight slides right in but the front required a little fitting. Here are some pictures.
    Liked On: 06-12-2014, 11:03 AM
  3. hombre243
    hombre243 liked post by paulrabe78 On thread : Doing my research into my 1st AR type rifle
    These have a blemish but the price is hard to beat. Adams Arms Base Piston Carbine 556NATO 16" BLK 6-POS Blem $599.00 SHIPS FREE...
    Liked On: 05-30-2014, 05:37 PM
  4. dreaded_rust
    dreaded_rust liked post by paulrabe78 On thread : PT 1911 sights
    Just for giggles last night I took the sights off my 1911. I put my Williams Fire Sights on it from my 24/7 Pro. They fit! I went to Williams website today and they list a set specifically for the...
    Liked On: 05-29-2014, 11:13 AM
  5. TexasAviator
    TexasAviator liked post by paulrabe78 On thread : PT 1911 sights
    Just for giggles last night I took the sights off my 1911. I put my Williams Fire Sights on it from my 24/7 Pro. They fit! I went to Williams website today and they list a set specifically for the...
    Liked On: 05-28-2014, 12:27 PM
  6. Smokewagon
    Smokewagon liked post by paulrabe78 On thread : Stupid AR Question
    All my guns are stored with the actions closed. Some are loaded most are not. Most are locked in safes.
    Liked On: 05-26-2014, 08:43 PM
  7. AOCM.RET
    AOCM.RET liked post by paulrabe78 On thread : Question on 223 loads
    Just make sure to seat them less than the maximum of 2.260 so they will fit your AR mag. I would seat those bullets between 2.200 to 2.250. And use a Lee Factory Crimp die as the last process...
    Liked On: 05-25-2014, 08:15 AM
  8. lapetrarca53
    lapetrarca53 liked post by paulrabe78 On thread : Questions on working up new loads
    With handgun loads I find a load that functions in my gun. I generally pick somewhere in the middle of the supplied load data. If the range is 4.5-5.0 grains of powder I will start at 4.6-4.7. I...
    Liked On: 04-08-2014, 10:00 AM
  9. Fishinkeylargo
    Fishinkeylargo liked post by paulrabe78 On thread : Primer Crimp removal
    This is what I use. Hornady Primer Pocket Reamer Package (http://www.midwayusa.com/product/804809/hornady-primer-pocket-reamer-package?cm_vc=subv1804809) I chuck it up in my cordless drill and it...
    Liked On: 04-07-2014, 11:09 AM
  10. Deadheadfred
    Deadheadfred liked post by paulrabe78 On thread : "Go-To" powders
    For pistol powder I like Hodgdon's Universal Clays, because it is so "Universal". I can be used for almost all pistol cartridges. For the calibers you've listed for rifles, look into Hodgdon's...
    Liked On: 03-27-2014, 07:50 PM
  11. kruizer@q.com
    kruizer@q.com liked post by paulrabe78 On thread : 840 C hammer bite
    I took my new 840 C to the range and I was getting hammer bite. Luckily I had some gloves with me so I only have a small blood blister on the web of my hand. Anybody else have this happen with a...
    Liked On: 03-23-2014, 01:02 PM
  12. AOCM.RET
    AOCM.RET liked post by paulrabe78 On thread : 840 C hammer bite
    I was shooting today in 20 degree weather and maybe that loosened my grip a little.
    Liked On: 03-22-2014, 08:44 PM
  13. GreenWolf70
    GreenWolf70 liked post by paulrabe78 On thread : New Reloader, Powder?
    My go to powder for .380 acp, 9mm, and .40 is Universal Clays.
    Liked On: 01-25-2014, 04:25 PM
  14. Texheim
    Texheim liked post by paulrabe78 On thread : My latest Mosin Nagant upgrades
    Well.... I bought a new used bolt, cut off the handle, bent a SS 3/8" by 4 1/2" bolt to the shape I wanted and welded it in place. Then I made the bolt knob and polished the whole thing up.
    Liked On: 12-28-2013, 06:46 AM
  15. aquajim
    aquajim liked post by paulrabe78 On thread : My latest Mosin Nagant upgrades
    Here is my Mosin 2 months ago post #24 http://www.taurusarmed.net/forums/other-long-arms/64743-mosin-nagant-3.html Since then I glass bedded a fiberglass rod to stiffen the forend of the stock,...
    Liked On: 12-28-2013, 04:54 AM
Page 1 of 15 12311 ... LastLast